Follow us :

  • The process characteristics of wire/rod drawing consists of (1) Pulling of the wire rod/round through the die to reduce its diameter, (2) Drawing increases the length of the wire/rod as its diameter decreases, (3) Several dies are used in succession (tandem) for small diameter wire,(4)At last ,the wire rod/round will be smaller ,but the length will longer .and more suitable in somewhere and more ...

  • Galvanized nails are coated with zinc to give them added corrosion resistance. Blued steel nails are subjected to a flame to give them a bluish oxide finish that provides a certain amount of corrosion resistance. So-called cement-coated nails are actually coated with a plastic resin to improve their grip.

  • A:The principle of wire drawing mchine are by the smaller drawing die diameters from one drawing step to the next the wire diameter is reduced by the diameter given through the drawing die. With a constant entrance speed of the wire the finished wire has a drawing speed after the last drawing die which is linear to the diameter reduction of the wire. This is equal for all individual drawing steps.

  • A:Well its depend on customer that which type of Nail Making Machine Model Choose it generally Nail Making Machine Speed is 350 Nail Per Minute. It means you can Produce 500 Kg Nail if you’re Nail Making Machine working 8 hour in a day.

  • A:1.first ,steel is immersed in a caustic solution to remove organic material such as grease and dirt, 2.followed by dipping in an acid bath (hydrochloric or sulfuric) to remove mill scale and rust, 3. finally lowered into a bath of flux that promotes zinc & steel reaction and retards further oxidation of the steel… (steel will not react with zinc unless it is perfectly clean)

  • A:Yes,wire mesh welding machine just as our other salling machine well ,can be tailor-made according to customer' s inquiry; but within the scope of our design for better efficiency and performance of the machines.please let us know what are your demands of it .

  • A:One of Our steel wire mesh welding machine/mesh welder purpose is specially designed to produce welded mesh for constructional purpose as in RC and SRC applications with reinforcement concrete.

  • A:Drawing dies are usually made of tool steel, tungsten carbide or diamond, all of which have surfaces of high hardness. Due to different sizes of wires, different dies are employed. A diamond die is used for drawing very fine wire. For hot drawing, cast-steel dies are used, while for steel wire drawing, a tungsten carbide die is used.Click to learn more about wire drawing machine

  • A:The wire is usually shrunk through pointing machine to fit through the die; then the wire is pulled through the die. As the volume of the wire remains the same, the diameter of the wire is getting smaller, the length will be longer. Broadly speaking, the wire needs a series of draw, through smaller and smaller dies, to reach the particular size.Click to learn more about wire drawing machine

  • Lubrication is an important part of drawing process, for its close relationship with good finish surface and long die life. Given different lubrication conditions, there are two types of wire drawing: wet and dry. Straight wire drawing machine is a dry drawing, for its wire or rod go through a lubricant container, while wet wire drawing machine refers to the wire or rod are completely immersed in ...

  • A:Wire drawing machine is designed to reduce the cross-section of a wire to a desired size through pulling the wire through a single or a couple of dies. There are many applications for wire drawing, including making nail 、screw ,electrical wiring, cables, spokes for wheels and stringed musical instruments.Click to learn more about wire drawing machine

  • 1. Trial running before delivery, offer finished product for customer confirmation.2. Shipping on time3. According to the customer credit status, provide the buyer's credit, the medium and long term credit, quality assurance

  • A:Please send us the product parameters you need. For example, if you need quotation for wire drawing machine, please provide us with following information by email: zmec..........com: 1. Raw material (high carbon steel or low carbon steel) 2.diameter of inlet and outlet wire 3. Required capacity (how many kg/8h) 4. Usage of your final product . We will prepare the proposal for you asap.

  • Q: What pre-sales service your company provide ?A:1.Free solution proposal.2.Configuring the equipment completely to the customer’s requirement. and we will provide the proposal to the customer who have no experience in this field.

  • Q:How long do you guarantee wire drawing machine ,what is the guarantee details?A:12 months after commissioning or 18months after shipment. Whichever first is in valid. (It is excluding wear parts. Shipping cost for parts to be replaced during warranty period has to be borne by the customer.)

  • Q:What is screw making machine woking progress?A: The progress as blow :Raw material Cold heading Thread rolling Screw

  • Q: What is the power of screw making machine ?A: Our screw nail making machine is with different power ccording different reuipment for screw nail machine detailed ,please refer to our quotation ?

  • We can according your requipments finding the optimum solutions to your investment ,and our really hope can help each of our clients set up a plant wist safety ,efficiency and accuracy .

  • Straight wire drawing machine is one type of more advanced and newer that drawing wire machine .1.Speed compare :Usually ,straight -line wire drawing machine pruduce speed is higher that wheel type wire drawing machine .2.Operating :Straight line wire drawing machine have installed advanced control system ,you just need control the machine by touch screen easy to control the machine speed and etc....

  • Q: Do we really needdescaling unit as a part of wire drawing process?A: Descaling is neededbefore drawing; it is used to remove rust and oxide on surface of wire.

  • Q: What is the consumption of Wire Drawing mold?A: one piece of wiredrawing mold min. for drawing 2 tons of wire.

  • Q: Consumption of Wire Drawing Powder?A: 2kg powder for drawing 1 ton of wire.

  • Q: What is usage of Wire Drawing Powder?A: Wire Drawing Powder isput in mold box, which is to lubricant and protect the wire.

  • Q: Could one set of machine make all sizesof screw?A:No, our machine has its production range, one machine could make screw withsome production range.

  • Q: What is usage of Slot Milling Machine?A: Making straight-line slot on head ofwood screw.

  • Q:Can you provide specification of raw material ?A:We will provide you size of raw material after we getdiameter of shank of all screws.

  • Q:What is the rawmaterial for screw?A:Low carbon iron wire, commonly from 1008 to 1022, different type of screw, different carbon content.

  • Q:How long do you guarantee nail making machines? What are the guarantee details? A:12 months after commissioning or 18months after shipment. Whichever first is in valid. ...

  • Q: What is the Delivery time for the nail making machines? A:60 days after receiving the down payment or L/C. ...

  • Q: What is raw material used for the Nail washing machine?A: Thematerial is sawdust (wood dust) and paraffin wax.

  • Q: What is the consumption of the NAIL MOULD, NAIL CUTTER & PUNCH PIN?A: Itis around 2 pairs each month if the machine works 8h/day.

  • Q: Does gabion wire spiral coiling machine could produce all different diameter's wire?A: Yes ,we have one complete changing gear suit fordifferent diameter’s wire.

  • Q: Why main customers choose gabion machine with width 4300mm?A: Because it is more efficiency, Gabion machine with width 4300mm couldproduce net width in fourfold in one time , 3meters+1meter ,2meters+2meters ,2meters+ 1meter+1meter,etc. meet difference customers request.

  • Q:How the blow moulding machine works and what is its parameter?A: Bottle blowing machineMain Technical ParameterTYPEITEMUNITHY-A6 technical dataContainerProduct material/PET /PCContainer volumeL1.5Theoretic outputPsc/hr4500Preform lengthmm50-200Max height of bottlemm320MoldingPreform inner diametermm15-60Bottle diametermm35-110Max mold plate dimension (L × W)mm380 × 460Max mold thicknessmm200Air ...

  • A:NO.346 Qingtai Street, Hangzhou, China.点击打开链接

  • Q:What is the name of your company?A:HANG ZHOU CANDID I/E CO .,LTD.

  • Q: What is capacity of gabion machine factory power supply?A: 50KW.

  • Q: What is total power of the gabion machine?A: 35KW.

  • Q: What is the main motor's capacity of gabion machine?A: 30KW.

  • Q: What is Number of twists for netting?A: 3/5, our gabion machine could produce 3 twists or 5 twists.